Safety instructions
All safety instructions must be read, followed and kept in a safe place.
DANGER — Reduce the risk of electric shock
- Never use the appliance if it is damaged, defective or has fallen into water, or if the charger is damaged.
- A damaged charger must always be replaced with an original part supplied by an authorised after-sales service centre.
- After a long period without use, have the appliance inspected by an after-sales service centre before putting it back into operation.
- Repairs and technical maintenance of the appliance must only be carried out by specialists trained in electrical engineering.
- Never touch an electrical appliance that has fallen into water. Immediately unplug the plug from the socket.
- Do not use an electrical appliance in a bathtub or under the shower.
- Always store electrical appliances so that they cannot fall or be knocked into a sink or bathtub. Avoid any contact between the appliance and water or any other liquid.
- Unplug the appliance immediately after use, except during charging.
- Unplug the appliance before cleaning it.
CAUTION — To avoid burns, fires, electric shocks and injuries
- This appliance must not be used by people (including children) with reduced physical, sensory or mental capabilities, or by people lacking experience or knowledge, unless they are supervised by a person responsible for their safety or have received instructions on how to use the appliance.
- Supervise children to ensure that they do not play with the appliance.
- Only use the appliance for the purpose described in the manual. Use only the combs recommended by the manufacturer.
- Do not use the appliance if the cable or plug is damaged, if it is not working properly, if it is damaged, if it has been dropped, or if it has fallen into water: have it inspected and repaired by an after-sales service centre.
- Keep the cable away from hot surfaces.
- Ensure that the ventilation openings are not obstructed by lint, hair, or other debris.
- Do not drop or insert any object into the openings.
- Do not use the appliance outdoors or in a place where aerosol products (sprays) are being dispersed.
- Do not use the appliance with a damaged or broken comb: this may cause injuries.
- Always connect the cable to the appliance first, then to the outlet. To unplug, switch off all controls (position « 0 »), then remove the plug from the outlet.
- Do not expose or store the appliance at temperatures below 0 °C or above 45 °C. Avoid direct exposure to sunlight.
- Follow all charging instructions and do not charge the appliance outside the range of 0 to 45 °C. Improper charging or charging at a temperature outside this range may damage the battery and increase the risk of fire.
CAUTION — Keep the appliance dry
- Do not use the appliance near pipes, water troughs, or other containers holding water.
- Use and store the appliance only in dry places.
- Never use the appliance with wet hands.
- Never use the appliance on a wet animal.
DANGER — Risk of explosion or fire
- Never use the appliance in an environment containing a high concentration of aerosol products (sprays) or in which oxygen is released.
- Do not use aerosols, sprays, lubricants, or disinfectant solutions. Use only the manufacturer's lubricant.
- Never disassemble, puncture, short-circuit, burn, or throw the lithium battery into a fire.
- Keep the lithium battery dry and never immerse it in water.
- Use the supplied charger only to charge the lithium battery.
CAUTION — Risk of injury from an overheated cutting head
- The cutting heads may become hot during prolonged use.
- Oil the cutting head every 5 to 10 minutes to limit overheating.
- The cutting head may become hot if the appliance operates for a long time without interruption: take regular breaks to let it cool down.
CAUTION — Injuries due to improper handling
- Do not charge, store, or leave the appliance in a place where it could be damaged by animals or the weather.
- Plug the charger directly into the outlet, without an extension cord. Unplug the charger from the outlet before plugging in or unplugging the appliance.
- Make sure the appliance is switched off (position 0) before plugging it into or unplugging it from the mains.
- Never leave the appliance plugged in unattended.
- Do not use damaged, broken, or blunt cutting heads.
- The cutting head has fine teeth with sharp edges that are dangerous when removed: handle and use it with care.
- After use, before removing or attaching a blade, and before any cleaning, maintenance, or storage, always switch off the device and remove the plug.
WARNING — Danger posed by and to animals
- Large animals can cause injuries: the noise of the device may irritate the animal and cause it to kick. Make sure the animal is calm and properly restrained.
- If necessary, wear eye, head, and ear protection, as well as safety shoes and gloves. Wear close-fitting clothing, remove jewelry, and tie back long hair.
- The animal's coat (or wool) must be dry and free of knots.
- Cables on the ground are dangerous: ensure that they cannot become tangled, that no one can walk on them, and that they are not soiled by excrement.
CAUTION — Risk of damaging the device
- Use the device exclusively with the voltage indicated on the rating plate.
- Use only accessories and combs recommended by the manufacturer.
- Do not insert or drop any objects into the openings of the device.
- Do not carry the device by the cable. To unplug it, always pull on the plug, never on the cable or the device.
- Keep the device and cable away from hot surfaces.
- Ensure that the cable is not twisted or pinched during use and storage.
Contents and specifications
Included accessories
- A — Power supply unit (with interchangeable plug adapters)
- B — Charger base
- C — Battery
- D — Cleaning brush
- E — R15 oil
Keep the case or storage bag to transport and store the device safely.
| Motor | 12 V BLDC motor |
|---|---|
| Dimensions (L × W × H) | 214 × 42 × 61 mm |
| Weight | approx. 844 g |
| Blade speed | 2,500 rpm |
| Sound level | 72 dB(A) at 1 m (uncertainty: 2.3 dB(A)) |
| Vibrations | 14.37 m/s² (uncertainty: 1.5 m/s²) |
| Rated power | 29 W |
| Operating voltage | 12 V |
| Lithium battery (B500-32) | Output voltage 10.8 V · capacity 3.2 Ah · INR18650-320 cells · 34.56 Wh · overload current 3.2 A |
| Charger base | Input 100–240 V AC, 0.8 A · output 12 V 2 A, 24 W |
Preparing the horse and the clipping area
- Check that the contents are complete.
- Check all parts for possible transport damage.
- Prepare a safe clipping area and take all necessary protective measures.
- Make sure the animal is properly secured and that its coat is clean and dry.
Installing the blade
CAUTION — Injuries and property damage may result from incorrect installation. Switch off the clipper and remove the battery before removing or installing the blade. Use the device only once the blade has been correctly installed, tensioned, and oiled.
Lister or Wahl blades are the most suitable and offer the best performance. Blades are manufactured in pairs (cutter and comb): always store and use them in pairs to extend their service life.
- Remove the battery from the clipper.
- Turn the device over and carefully place the blade (upper blade) on the clipper head. The crank wheel must fit into the blade’s notch.
- Position the comb (lower blade), ensuring that its two holes engage with the two pivots.
- Insert the clamping screw into the central hole.
- Slide the spring onto the clamping screw and firmly tighten the clamping nut.
- Adjust the tension (see below).
Adjusting the tension
- Hand-tighten the clamping nut as far as it will go.
- Then loosen the nut by one and a half turns to adjust the tension, using the mark on the nut as a guide.
CAUTION — Incorrect tension may cause injury and property damage.
- Excessive tension dulls the cutting head and causes it to overheat.
- Insufficient tension reduces cutting power and clogs the cutting head.
Oiling
- Brush excess hair from the cutting head and the clipper.
- During clipping, oil the cutting head every 5 to 10 minutes with R15 oil. Run the device briefly to distribute the oil, then switch it off and wipe off the excess.
Oiling points:
- Between the teeth of the cutting head, with the device head facing upward to distribute the oil between the blades.
- On the contact surfaces between the device head and the blade.
- At the rear of the cutting head, on both sides, tilting the device head to the side to distribute the oil over the rear surfaces.
- In the cutting head’s guide channels, through the two holes, tilting the device head to the side.
- On the crank and its wheel, through the central hole.
CAUTION — Incorrect oiling may cause injury and property damage.
- Oil the cutting head frequently.
- Use only R15 oil: other lubricants may irritate the animal’s skin.
- Aerosol lubricants contain solvents that can damage the device or the cutting head.
Clipping: switching on and resetting
- Insert the charged battery into the clipper until the locking clips engage on both sides.
- Switch on the device by pressing the On/Off button once.
- After use, switch off the device by pressing the On/Off button once.
- To check the approximate charge level, switch off the device and press the battery’s “Fuel Gauge” button (charge indicator).
| Lights on | Charge level |
|---|---|
| 1 | 0 to 33% |
| 2 | 34 to 66% |
| 3 | 67 to 100% |
Reset
- The device returns to the factory settings every time you remove and reinsert the battery.
- If the cutting head appears to slow down during use, check the battery charge level. If the battery is sufficiently charged, clean and oil the cutting head, then reset the device by removing and reinserting the battery.
Charger base and battery charging
Installing the charger base
Place the charger base on a stable, level, dry, and clean surface.
- Choose the plug adapter suitable for your mains socket and attach it to the power supply until it clicks into place.
- Connect the charging cable to the charger base in the correct orientation.
- Connect the power supply to the mains socket.
Charging the battery
DANGER — Risk of explosion or fire. To charge the lithium battery, use only the supplied charger base and the corresponding power supply.
A new battery only reaches its full capacity after three successive charge and discharge cycles.
- To remove the battery from the clipper, press both locking clips simultaneously, one on each side.
- Check that the battery terminals are free of foreign objects and dirt.
- Place the battery in the charger base compartment so that it rests on the connectors.
- The lights remain continuously lit and indicate the current charge level: the battery is charging.
- When the battery is charged, the three lights on the base switch off. A full charge takes 130 minutes. Partial charging and discharging do not damage the cells. Unplug the charger when not in use.
- Insert the charged battery into the clipper until the clips on both sides engage.
When fully charged, the clipper operates for approximately two hours (about 130 minutes according to the original English version of the manual). Charge the battery before use.
Battery handling and overload protection
DANGER — Risk of explosion or fire
- Never disassemble, puncture, short-circuit, or burn the battery, and never throw it into a fire.
- Keep the battery dry and never immerse it in water.
- The battery contains no user-serviceable parts. Never attempt to replace the lithium battery cells. Never ship a defective battery (by mail or carrier).
- If the appliance is to remain unused for an extended period, remove the battery.
- The battery terminals must not be short-circuited.
Battery storage
The battery must be stored fully charged. It may gradually lose its charge during long-term storage: fully recharge it for 130 minutes every 6 months. If it has lost most of its charge, it will only regain its full capacity after three charge and discharge cycles.
Overload protection
The battery contains a protective fuse that cuts off the power if the cutting head jams. If it has tripped, inspect the cutting head and check that hair or fleece is not clogging the blades. Remove any foreign objects and replace a damaged cutting head.
To reset the protection, remove the battery from the clipper and then reinsert it. You can then resume clipping.
Cleaning and storage
- Wipe the handle with a soft cloth. Brush away all hair and dirt from the cutting head and the device head.
- Remove the cutting head for cleaning, taking care not to lose the tension spring. Oil the cutting head before storing it.
- Store the device in a clean, dry, and safe place.
DANGER — Risk of electric shock due to liquid ingress. Do not immerse the device in water or allow any liquid to enter it. Connect it to the power supply only when it is completely dry.
CAUTION — Harsh chemicals. Never use solvents or abrasive products, which may damage the device or its accessories. Wipe the device only with a slightly damp soft cloth.
Sharpening, blade replacement, and repairs
If cutting performance decreases, the cutting head must be sharpened or replaced. Remove and reinstall it (or fit the new one) by following the steps “Fitting the cutting head” and “Adjusting the tension”.
For accessories and spare parts, contact us.
DANGER — Risk of explosion or fire. The battery contains no user-serviceable parts. Never attempt to replace the lithium battery cells. Never ship a defective lithium battery.
Disposal
Proper disposal protects the environment and prevents harmful effects on people and the environment. Comply with applicable regulations.
- Never disassemble, puncture, or burn the lithium battery, and never throw it into a fire.
- Do not dispose of the device or the lithium battery with household waste.
- Remove the used battery from the device and place it in a battery collection container or at a local collection center that will process and recycle it in accordance with applicable regulations.
- In the European Union, Directive 2012/19/EU on waste electrical and electronic equipment (WEEE) prohibits disposing of the device with household waste: it is collected free of charge by local collection points or recycling centers.
- The packaging is made of recyclable materials: take it to a recycling facility.
The device is covered by an EC declaration of conformity, available from the manufacturer on request.
Manufacturer: Lister Shearing Equipment Limited, Stonehouse (United Kingdom), a subsidiary of Wahl Clipper Corporation. C500 model. Manual based on the manufacturer's instructions for use (French version, July 2024).
