Specifications

• Quick wireless installation with magnetic or hook-and-loop fastening.
• 12.7 cm screen for high-quality images.
• Infrared for seeing in the dark.
• Video recording possible on a microSD card (not included).
• Reliable long-range signal, stable connection up to 100 m.
• At least 12 hours of battery life for worry-free travel.
• Two charging modes: USB-C cable or solar power.
• Fast 2.4 GHz transmission for clear, real-time video.
• IP65 waterproof design, resistant to rain, dust and harsh travel conditions.

Box contents

• 1 rechargeable camera with magnetic base
• 1 USB Type-C charging cable
• 2 2.4 GHz high-gain 5 dB antennas
• 1 12.7 cm screen
• 1 suction cup windshield mount
• 1 power cable for cigarette lighter socket (with switch)
• 2 metal plates with 3M hook-and-loop fastener
• 1 user manual

Quick start

1. Fully charge the camera using the USB Type-C charging cable.
2. Screw the longer antenna onto the camera and the shorter one onto the screen. Bend the antennas at their joints.
3. Attach the camera inside the van using the magnetic base or the adhesive hook-and-loop plate. Place it high up so that your horse cannot reach it! With the hook-and-loop fastener: separate the two sides, remove the protective film and stick the “velvet” side inside the van. Then position the plate with the “hooks” side onto the velvet: the camera is held in place by the magnets.
4. Press and hold the camera’s power button to turn it on. A blue light flashes slowly near the button. The easiest way is to rotate the camera for easy access to the button.
5. Hand-tighten the side nuts so that the camera does not tip over during the journey.
6. Connect the screen to your vehicle’s cigarette lighter socket / power outlet. Press the red button on top of the plug so that the red light comes on. In some vehicles, the ignition must be turned on to power the screen.
7. The screen should start automatically and display the camera image. If not, see the Troubleshooting section.
8. Attach the suction cup to a flat surface and install the screen.

The screen and its buttons

The three control buttons are on the back of the screen, on the left side.

Displayed icons

The system allows the screen to turn off after an adjustable period. It must be set to “always on”: see Troubleshooting if the screen turns off.

Charge the camera

Connect the camera with the USB Type-C charging cable.

Record a video or take a photo

1. Insert your micro SD card.
2. Briefly press MENU to start recording.
3. Briefly press MENU to stop recording.
4. Press briefly « - » to take a photo.

If the screen asks you to format the SD card

1. Hold down MENU.
2. Press + UP until you reach the “settings” menu.
3. Press MENU to select it.
4. Scroll down with - DOWN to “format SD card” (format the SD card).
5. Press MENU.
6. You must delete all files to format the card.
7. Select “yes” with + UP, then press MENU.

View your recordings

1. On the screen, hold down MENU.
2. Select the video by pressing MENU.
3. Scroll through your videos and press MENU to watch.

Screen settings

All the following settings start in the same way: hold down MENU, press + UP until “settings” appears, then select it with MENU.

Change the language

1. Open « settings » as indicated above.
2. Scroll down with - DOWN to “Language” (language).
3. Press MENU.
4. Navigate the menu with + UP.
5. Press MENU on the desired option.

Set the date or time

1. Open « settings » as indicated above.
2. Scroll down with - DOWN to “Date/time” (date/time).
3. Press MENU.
4. Choose the desired date format with + UP and - DOWN, then press MENU.
5. Set the date and time using the scroll buttons, pressing MENU when the value is correct, then press MENU to finish.

Correcting a mirrored or upside-down image

1. Open « settings » as indicated above.
2. Scroll down with - DOWN to « picture flip » (image flip).
3. Press MENU.
4. Navigate the menu with + UP.
5. Press MENU on the desired options. You must first select a mirror option before you can move on to the flip options.

Adjusting the screen brightness

1. Open « settings » as indicated above.
2. Scroll down with - DOWN to « back light brightness » (backlight brightness).
3. Press MENU.
4. Choose the desired brightness with + UP and - DOWN, then press MENU.

Show or hide the reversing guide lines

Hold down the « + » button for 3 seconds to show or hide them.

Troubleshooting

The screen is not paired with the camera

The screen is normally paired with the camera at the factory. If it is no longer paired, proceed as follows:

1. Turn on the camera with the power button: a blue indicator light flashes steadily.
2. Immediately press the power button three times in quick succession.
3. On the screen, hold down MENU.
4. Press + UP to go to « settings » (settings).
5. Select « settings » by pressing MENU.
6. Scroll down with - DOWN to « Pairing » (pairing).
7. Press MENU to select the camera.
8. The screen restarts automatically.

The screen and camera turn off after a while

1. Open « settings »: hold down MENU, press + UP until you reach « settings », then select it with MENU.
2. Scroll down with - DOWN to « camera working time setting » (camera operating time).
3. Press MENU.
4. Scroll through the options with + UP.
5. Once you reach « always on » (always on), press MENU.

You can also choose a duration before the screen turns off. The screen has a motion detector that automatically switches to energy-saving mode if no movement is detected for the selected duration: the screen and camera turn off without any action on your part. To reactivate them, simply move your hand within 4 inches (approximately 10 cm) of the screen.

If you have any questions, please contact us.

Manufacturer: Woof Wear (WW Technology). French translation of the manufacturer's instructions.